Mechanical Properties of Selected Indigenous Timber Species from Southwestern Nigeria: A Comparative Study for Structural Applications
DOI:
https://doi.org/10.70028/sgm.v2i2.45Keywords:
Timber, Mechanical Properties, Structural Suitability, Flexural Strength, ConstructionAbstract
The demand for sustainable and cost-effective construction materials in Nigeria has renewed interest in the structural use of indigenous timber species. However, the absence of standardized mechanical data on many local timbers has limited their acceptance in structural applications, often resulting in reliance on traditional knowledge rather than empirical evidence. This study
investigates the mechanical properties of four indigenous timber species from Southwestern Nigeria—Anogeissus leiocarpus (Ayin), Albizia ferruginea (Alakrity), Pterocarpus erinaceus (Ayere), and Ricinodendron heudelotii (Eru)—to evaluate their suitability for structural use. Standard laboratory tests were conducted to determine the modulus of rupture (MOR) and modulus of elasticity (MOE) under both wet and oven-dried conditions using uniformly dimensioned specimens. The results revealed significant differences in strength and stiffness among the species. In the oven-dried condition, Anogeissus leiocarpus recorded the highest MOR of 3.1 MPa, outperforming Albizia ferruginea by 22.6%, Ricinodendron heudelotii by 9.7%, and Pterocarpus erinaceus by
38.7%. Similarly, in MOE, Anogeissus leiocarpus showed the highest value of 50.8 MPa, exceeding Albizia ferruginea by 2.6%, Ricinodendron heudelotii by 5.5%, and Pterocarpus erinaceus by 7.9%. Across all species, oven-dried samples consistently exhibited superior mechanical performance compared to wet samples. These findings provide critical comparative data to inform material
selection in construction and promote the effective utilization of indigenous timber resources. The study contributes to advancing sustainable construction practices in Nigeria by encouraging reliance on locally sourced materials, reducing dependence on imported timber, and supporting environmentally responsible building solutions.
Downloads
References
Forest Products Laboratory, Wood Handbook – Wood as an Engineering Material, General Technical Report FPL-GTR-190. USDA Forest Service, 2010, doi: http://dx.doi.org/10.2737/FPL-GTR-190
R. J. Ross, Ed., Wood Handbook: Mechanical Properties of Wood, USDA Forest Service, 2010. doi: http://dx.doi.org/10.2737/FPL-GTR-190
D. E. Kretschmann, “Mechanical Properties of Wood,” in Wood Handbook, USDA Forest Service, 2010.
D. W. Green and J. W. Evans, Mechanical Properties of Wood, USDA Forest Service, 2003.
J. Bodig and B. A. Jayne, Mechanics of Wood and Wood Composites, Krieger Publishing Company, 1993. Available: https://archive.org/details/mechanicsofwoodw0000bodi
W. T. Simpson, Drying and Moisture Relationships of Wood, USDA Forest Service, 1991.
European Committee for Standardization, EN 338: Structural Timber – Strength Classes, 2009. Available:https://standards.iteh.ai/catalog/standards/cen/f1a01242-978b-46bf-b0c9-
ab4da366/en-338-2009
British Standards Institution, BS 5268: Structural Use of Timber, 2002. [Online]. Available: https://knowledge.bsigroup.com/products/structural-use-of-timber-code-ofpractice-for-permissible- stress-design-materials-and-workmanship.
A. A. Jimoh and A. A. Ibitolu, “Classification of Selected Nigerian Timbers Using EN 338,” Journal of Building Performance, vol. 9, no. 2, pp. 24–31, 2018.
O. S. Lamidi et al., “Mechanical Characterization of Underutilized Nigerian Timber,” Nigerian Journal of Technology, vol. 41, no. 3, pp. 54–62, 2022.
M. A. Rahmon and A. A. Jimoh, “Comparative Strength Classification of Selected Timbers,” Construction and Building Materials Journal, vol. 211, pp. 95–103, 2019.
A. A. Ogunwusi and M. A. Jolaoso, “Forest Products and Sustainable Housing Development,” Journal of Sustainable Development in Africa, vol. 14, no. 3, pp. 44–57, 2012.
F. O. Ezeudu and E. Nwankwo, “Strength Characteristics of Iroko and Teak,” Nigerian Journal of Wood Science, vol. 5, no. 1, pp. 15–22, 2017.
A. O. Ogunleye et al., “Characterization of Some Indigenous Timbers for Structural Use,” Scientific Research Journal, vol. 8, no. 1, pp. 112–121, 2020.
R. E. Olagunju and K. Ogedengbe, “Sustainability Challenges in Nigeria’s Timber Industry,” Journal of Built Environment Research, vol. 3, no. 2, pp. 34–41, 2021.
S. A. Aguda et al., “Mechanical Evaluation of Ficus vallis-choudae,” Journal of Applied Sciences & Environmental Management, vol. 24, no. 6, pp. 1017–1022, 2020.
A. S. Mohammed et al., “Strength Classification of Terminalia ivorensis,” Nigerian Journal of Engineering, vol. 26, no. 2, pp. 80–88, 2019
E. J. Akpan and E. I. Ekong, “Physical and Mechanical Properties of Afzelia africana,” African Journal of Engineering Research, vol. 9, no. 4, pp. 142–150, 2021.
R. B. Hoadley, Understanding Wood: A Craftsman’s Guide to Wood Technology, Taunton Press, 2000. Available:https://www.amazon.com/Understanding-Wood-CraftsmansGuideTechnology/dp/1561583588
R. J. Ross et al., “Wood in Civil Engineering Applications,” American Society of Civil Engineers, 2015.
O. A. Wilson et al., “Strength Grading of Northern Nigerian Timbers,” African Journal of Engineering Research, vol. 9, no. 1, pp. 12–19, 2021.
Y. M. D. Adedeji and S. K. Adeyoju, “An Appraisal of Timber Use in Nigeria’s Building Industry,” Covenant Journal of Research in the Built Environment, vol. 1, no. 2, pp. 17–29, 2012.
S. O. Bada et al., “Prospects and Challenges of Indigenous Timber Testing in Nigeria,” Journal of Forestry Research, vol. 33, no. 1, pp. 77–86, 2022.
A. M. Adebayo and J. A. Fuwape, “Timber Utilization in Informal Construction Sectors in Nigeria,” Journal of Environmental Research and Policy, vol. 4, no. 2, pp. 21–29, 2019.
A. Akinyemi et al., “Establishing Regional Timber Testing Labs for Nigeria,” Journal of Structural Materials and Engineering, vol. 5, no. 2, pp. 65–74, 2023.
ASTM D198: Standard Test Methods of Static Tests of Lumber in Structural Sizes (2022). ASTM International.
ASTM D4442: Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials (2020). ASTM International.
Downloads
Published
Issue
Section
License
Copyright (c) 2025 Tomisin Victor Kehinde (Author)
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
